2018 Dodge 5500 4×4 Versalift VST40 Aerial Truck


Request Quote


1)VERSALIFT VST-40-I, insulated 40ft. 4 in (12.3 m) telescopic aerial platform lift, 45ft. 4 in working height with a horizontal reach of 30 ft.2 in.

-Standard platform capacity of 400 lbs

-TruGuard™ dielectric isolating system with right hand single-stick control.

-Hydraulic platform rotator.

-Hydraulic dual arm articulating jib pole and winch package for up to 1,000 lbs. (454 kg.) capacity, including insulated jib pole

-360o continuous rotation including slip rings

-Six GPM (22.7 lpm) open center hydraulic system with a 3000 psi (210 kg/cm²) operating pressure

-Side mounted telescopic upper boom allows low stowing of platform.

-Fiberglass inner boom and patented ELECTROGARD provide insulation gap of 46 inches (1.2 m) fully retracted meeting ANSI A92.2 requirements for Category C 46KV and below.

-Chassis insulating system (fiberglass lower boom insert) providing 12 in. (0.30 m) insulation gap and including accommodations to bridge insulation gap for testing per ANSI 92.2

-ELECTROGARD and inner boom finished with white urethane paint over a white gel coat.

-Non-lube bearings used throughout.

-One set of hydraulic tool outlets with pressure limit valve. Valve can be adjusted from 1000 to 2500 psi.

-Sub frame mounted main A-frame outriggers with pivot feet, two control valves, and a selector valve.

-Outrigger boom interlock system for main outriggers

-Integral reservoir with a 17-gallon (64.4 l) capacity and dual sight gauges.

-Side mounted closed heavy-duty one-step 24 in. X 30 in. X 42 in. (0.61m X 0.76m X 1.07m) fiberglass platform including platform liner and vinyl cover.

-Individual full pressure controls at the turret actuate all boom functions and is equipped with a selector valve  to override upper controls

-12 Volt DC backup pump providing power to all boom functions.

-Automatic throttle control.

-Auto boom latch for mounting on outer boom ELECTROGARD. The rotary auto boom latch works off the lift hydraulic pressure to open and close.

-Standard white urethane paint

-Safety harness and lanyard

-Two operator manuals and service manuals

1) 2018 Dodge 5500 4×4 cab and chassis with a CA of 84”

-GVWR: 19,500 lbs payload.

-6.7L I6 Cummins Turbo diesel engine

-6-speed Aisin AS69RC HD automatic transmission

-Heavy duty front suspension group

-4.44 limited slip axle.

-Air conditioning.

-Cold weather group including engine block heater

-225/70Rx19.5G all traction tires.

-AM/FM radio

-HD vinyl 40/20/40 slit bench seat

-Parkview rear back up camera

-Ambulance prep package including 220 amp alternator

-Transfer case skid plate shield

-Painted Bright White clearcoat.


1) Dakota Bodies 132” long x 40” high x 94” wide service body including the following:

-30 inch tread plate platform extension

-LED lighting package installed in tail shelf with additional cutouts for strobe lights

-Cable access step at rear and side access.

-Two (2) chrome grab handles at side access and two (2) pool type grab handles for rear tail shelf.

-Wheel chock storage with pendulum retainers and outrigger pad holders.

-Master door lock hook and loop system on each door with two (2) spring loaded door handles. Excludes 1st vertical curbside

-Grey Zolatone paint on the interior of compartments.


Installation to include the following:

-VERSALIFT VST-40-I, mounting hardware, PTO and pump.

-Dakota service body and accessories.

-Combo pintle hitch, D rings and 7 prong trailer connector.

-Two (2) amber strobe lights in tail shelf and two (2) strobe lights in front grill.

-Grounding kit, park brake interlock system, back up alarm and mud flaps.

-Supply outrigger pads, wheel chocks, fire extinguisher, and 3 piece triangle reflector kit.

-Test ride completed unit for one (1) hour.

-Certify per ANSI A92.2