Description
Available NOW!!!! Current Location – Pennsylvania
1)Versalift Model SST36NE, non-insulated, one-man aerial tower
-Aluminum telescoping extension boom providing 41′ of working height.
-Engine start/stop at platform and lower controls
-Electric over hydraulic type controls at upper and lower control stations.
-Overriding controls at the pedestal.
-Worm gear rotation with an electric rotation limit switch.
-180 degree manual bucket rotator.
-Cat-track carrier system.
-Safety “D” ring on boom for attachment of lanyard.
-Prime painted.
-Rear torsion bar assembly.
-Two (2) operations, maintenance and parts manuals.
-120-volt wiring with double weatherproof GFI protected 15-amp outlets.
-Emergency 12V DC hydraulic system.
-Back-up warning device, electric horn type.
-Inclinometers installed for compliance to ANSI requirements.
-Side hung basket 24″ X 24″ X 42″ fiberglass walk-in basket with accessory cavity.
-Opening to open towards the pedestal area.
-Master/slave hydraulic leveling system Vinyl basket cover with elastic binding.
-RIGHT hand hinged as viewed from outside of basket.
-Door hinge supports for added hinge to door support.
-Standard basket capacity of 350 lbs.
-Drain Holes drilled into floor.
-Non skid bucket floor.
-Rubber coated “U” saddle boom rest.
-Heavy-duty square tubing and braced boom rest.
-Assembly braced and gusseted to provide long-term strength for this component.
-Hydraulic power provided by a transmission mounted PTO driven pump
-Shell Tellus 22 biodegradable hydraulic oil.
1)Dimensions Unlimited Model DUI-12/1800N
-DC to AC power inverter.
-Inverter is pure-sine wave 1800 watts continuous
-Equipped with automatic electronic short-circuit and overload protection.
-Automatic over temperature shutdown, output circuit breaker, and automatic low battery shutdown.
-One (1) deep cycle battery mounted in load area box to provide system support.
-All heavy duty wiring run in protective conduit or loom.
-Inverter in front curbside compartment and battery box in cargo area.
-Protective coatings to all electrical terminals.
-TST electrical system
1)108″ Steel aerial tower body
-Stainless steel paddle handle with rotary latch to pin striker type door latches
–A-60 galvaneal steel doors
–Automotive type door seals
-18″ deep compartments with 58″ wide body load area
-Four (4) vertical and two (2) horizontal compartments
-Hotstick storage compartments, streetside
-1/8” treadplate on top of side compartments
-Drip molding on leading edge of all doors
-Wheel chock storage, with retainer bar, two (2) in body fender panel both curbside
-Rubber door bumpers
-Fender crowns rubber on wheel openings
-Composite tailboard
-Complete prep and primer application.
-Linex coating applied to the cargo floor and tailshelf area.
-Undercoating applied to all body, tailshelf and upfitter added items.
-Combination ICC bumper and tailshelf access step on right side.
-Step approximately 24” wide x 10” deep grip strut
-Rear mud flaps.
-Two-inverted “U” handrail at rear of tailshelf, one at each side.
-One (1) pair rubber wheel chocks with handle.
-9-lamp modular lighting package.
Trailer towing package
-Square type receiver mounted at rear of chassis frame.
-Removable combination ball/pintle hook assembly
-6 way trailer socket, Safety chain eyes,
-Fire extinguisher 5 lb.
-D.O.T triangle type road reflector kit.
-Aerial tower painted standard white urethane.
-Powder coated exterior of utility body.
-ICC bumper gloss black.
1)2019 Ford F-450 4×2
–60” Cab to axle
-Gasoline engine
-6-speed automatic transmission with PTO provision
-Power brakes with 4-wheel anti-lock disc brakes
-Heavy-duty alternator
-Front stabilizer bar
-Tinted glass
-Fold away exterior trailer towing mirrors
-Gray vinyl bench seat
-40 gallon fuel tank
-Oil gauge
-Cigar lighter (Power Point)
-AM/FM stereo radio with clock
-Interval windshield wipers
-Painted OEM White
-Air conditioner
-Brake Controller
-OEM cab steps-running boards
